Discovering Essential Plumbing Skills is Crucial For Installing a Bathtub
Discovering Essential Plumbing Skills is Crucial For Installing a Bathtub
Blog Article
How do you really feel with regards to Installing A Bathtub?
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is readily obtainable, the job can move speedily; if you have to open up a wall to get rid of the old tub as well as position the brand-new bath tub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will need an assistant to vacate the old bathtub and set in the new one. Make sure you have actually qualified on your own for the work and also are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to consider utilizing one before you start. Chances are you might require a professional plumber to make tube connections.
This short article will assist you set up a new bathtub in your shower room if you have already bought a brand-new bathtub as well as don't require to alter the plan of your previous supply of water pipes.
Your devices as well as material list ought to comprise the following:
Planning for the Installation
Firstly, the sustaining frame provided with the bath should be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is detach the water supply. After doing so, activate the faucets to drain any kind of water remaining in the system. The process of removing the existing faucets can be rather problematic because of the restricted access that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a towel all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub up until the level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water as well as examine all joints and also new pipework for leaks and tighten them if required. Load the bathtub as well as also examine the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's instruction manual. Tiling as well as securing around the bath tub must wait until the bath tub has been used a minimum of when as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers remain in place between the faucet as well as the sink. Protect the faucet in position with the producer provided backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap adapters. The former type must be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, causing difficulties with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealer can crack rather very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly readily available on the market. It is suggested to fit the ceramic tiles using water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our excerpt about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for spending some time to read our blog post. Sharing is caring. Helping people is fun. Many thanks for your time invested reading it.
Expert consultation available. Report this page